NOCO Commercial Doors

24/7 Commercial Roll-Up Door Repair for Warehouses & Industrial Facilities

Broken spring? Curtain off track? Door stuck open with the shift ending? Rolling steel door failures shut down docks and leave buildings unsecured. Get 24/7 rapid dispatch from Northern Colorado & North Metro's Dedicated Commercial Door Dispatch.

Call 24/7 · Press 1 for Commercial Service: (720) 500-7480
  • 24/7 Emergency Dispatch
  • Commercial & Industrial Doors Only
  • Springs, Slats, Cables & Operators

Emergency Rolling Steel Door Repair

A rolling steel door that won't open stops freight. One that won't close leaves product, equipment and the building exposed. Emergency calls get priority emergency response so your facility can be secured or back in service.

Broken springs & high-cycle spring replacement

  • Symptoms: a loud bang, a door that won't lift or feels far heavier on the chain hoist, an operator that hums and stalls.
  • Torsion springs inside the barrel are sized to curtain weight, door height and barrel diameter. Wrong sizing causes the next failure.
  • Replacement springs can be upgraded to high-cycle torsion springs rated in the 25k–100k cycle range for doors that run all day.
  • Spring tension is set and balanced so the operator isn't straining against the curtain.

Off-track curtains & bent slat replacement

  • Curtains come out of the guides after impact, wind load or a worn end lock.
  • Bent 22-gauge and 24-gauge rolling steel slats are removed and replaced with matching profile and gauge, so you don't need a full new curtain.
  • Missing or worn end locks and windlocks are replaced to keep slats seated in the guides.
  • The curtain is re-fed, aligned and cycled under the operator before you take it back.

Snapped lift cables & drum problems

  • Applies to coiling doors and heavy sectional doors that use cable-and-drum lift.
  • A frayed or snapped cable can drop one side of the door and rack it in the tracks. Stop using the door immediately.
  • Cables, drums and set screws are replaced as a matched set, and both sides are tensioned evenly.

Forklift-damaged guides & bottom bars

  • Bent guides bind the curtain and wear slats fast. They are straightened or replaced and re-anchored.
  • Crushed bottom bars are replaced, along with the bottom astragal seal, to restore the seal at the floor against wind, dust, pests and heat loss.
  • Bollards and guide protectors can be recommended where the same opening keeps getting hit.

Door stuck open or shut right now?

24/7 rapid dispatch for commercial and industrial doors only.

Call 24/7 · Press 1 for Commercial Service: (720) 500-7480

Commercial Door Operator & Controls Repair

Jackshaft & hoist operators

  • Diagnosis and repair on LiftMaster, Genie and Manaras jackshaft and hoist operators: motors, gearboxes, brakes, clutches, limit switches and logic boards.
  • Like-for-like operator replacement when a unit is beyond repair, sized for door weight and duty cycle.
  • Manual chain hoist checked so the door can still be operated during a power loss.

Photo-eyes, safety edges & entrapment protection

  • Misaligned or failed photo-eyes and reversing edges are a top cause of "door won't close" calls.
  • Monitored entrapment protection is tested and restored. A door is never returned to service with safety devices bypassed.

Push-button stations & interlocks

  • Three-button stations, key switches, pull cords and remote controls repaired or replaced.
  • Interlocks with dock levelers, vehicle restraints and alarm systems are checked so equipment runs in the correct sequence.

High-Cycle Spring Upgrades for Busy Docks

When a standard spring is undersized

  • Many rolling doors ship with springs rated for a modest cycle count. Put one on a 3PL dock or a busy shop door and it can wear out fast.
  • If the same door keeps breaking springs, the spring is undersized for the job. That's not bad luck.
  • A high-cycle torsion spring uses heavier wire and a longer spring to spread the stress, so each spring lasts through more cycles.

Cycle counts and planned replacement

  • Count your cycles: daily opens per door multiplied by operating days. That number decides the spring rating you need.
  • Springs in the 25k–100k cycle range let you plan replacement during PM visits, so you aren't reacting to a broken spring in the middle of a shift.
  • Spring condition is logged at each maintenance visit so replacements can be budgeted ahead of time.

Repair or Replace a Rolling Steel Door?

Signs a curtain or barrel is at end of life

  • Widespread slat damage, corrosion or failed end locks across much of the curtain.
  • A bent or out-of-round barrel, worn bearings or brackets cracked at the wall.
  • Repeated off-track events even after guides and slats are repaired.
  • An obsolete operator with parts no longer available.

Planning replacement around downtime

  • When replacement makes sense, get the curtain, barrel, springs and operator quoted as one package.
  • Install timing is planned around shipping schedules, night shifts or slow days to keep docks running.
  • In the meantime, the existing door can be repaired to a safe, secure condition.

Emergency Repair Service Areas

Loveland & Windsor

Service along the I-25 corridor, Centerra and Great Western Industrial Park. → Loveland · Windsor

Related services: High-speed doors & operators · NFPA 80 fire door drop testing · Loading dock doors & levelers

Get the door closed, secured and running again.

Call 24/7 · Press 1 for Commercial Service: (720) 500-7480

Roll-Up Door Repair FAQs

What should I do if a roll-up door is stuck open overnight?

Clear people and vehicles away from the opening. Don't force the door with the operator, and don't try to adjust springs or cables yourself, because they hold dangerous tension. Then call (720) 500-7480 and press 1. Emergency calls are put on priority emergency response, and the technician's first job is to get the opening secured.

Can a broken commercial door spring be replaced the same day?

Often, yes. It depends on the spring size and whether it's in stock. Give dispatch the door width and height, and the barrel or spring label if you can see it. If a matching spring isn't available right away, the door can be secured until the correct high-cycle spring arrives.

Why does my rolling steel door keep coming off track?

The usual causes are bent guides from impact, worn or missing end locks and windlocks, a damaged bottom bar, or an operator over-traveling past its limits. Re-feeding the curtain fixes the symptom. Replacing the damaged guide, slats or end locks and resetting limits keeps it from happening again.

What are high-cycle springs and do I need them?

High-cycle torsion springs are built for more open-close cycles than standard springs, typically rated in the 25k–100k cycle range. If a door runs many times per shift or keeps breaking springs, an upgrade usually costs less over the life of the door than repeated emergency replacements.

Is it cheaper to repair or replace a damaged rolling steel curtain?

If the damage is limited to a few slats, the bottom bar or a guide, repair almost always wins. If damage, corrosion or failed end locks run across much of the curtain, or the barrel is bent, replacement can be the better long-term spend. You'll get both options to compare.

A Broken Roll-Up Door Doesn't Wait for Business Hours.

Springs, slats, cables, guides and operators. Get 24/7 rapid dispatch across Commerce City, Greeley, Loveland and Windsor.

Commercial and industrial doors only.

Request Dispatch or a Commercial Door Quote

Tell us the door and the problem. For a door down right now, calling (720) 500-7480 is the fastest route to dispatch.

Service Needed (required)

Commercial and industrial facilities only. For emergencies, call (720) 500-7480 24/7.

Call 24/7 Dispatch: (720) 500-7480